Events

Micromine Pitram Data Acquisition records "time-stamped" events. The time recorded is either the computer system time of the Micromine Pitram server or the computer system time of the Control Room Operator's computer.

Every event is logged to a special database table, with the first event in each table recording the start time of the shift. Immediately following this, a series of events are generated automatically by the system, setting the last known (from the end of the previous shift) "Allocation" and "Status" of each equipment unit.

The last event recorded is the end of shift. Start of Shift and End of Shift events can be configured to occur automatically, or they can be entered manually by the Control Room Operator. Shift Start and Shift End provide the basis for defining the total elapsed duration monitored for the shift.

During the shift, Micromine Pitram allows the Control Room Operator to enter changes in status that affect the whole shift (meetings, lunch breaks etc.). These Shift events will set all operating equipment units to idle when the event occurs, and then return those units to their operating status when the shift resumes.

The events recorded by Data Acquisition may be obtained via:

  • Voice communications. Each equipment Operator, using radio communications, reports all status changes and measures to the Control Room Operator. These changes, and any other verbal or written reports, are entered manually into the database.
  • Automatic communications. At an automated Micromine Pitram site, mobile devices provide the link between the Control Room Operator, the equipment operators, and the Micromine Pitram database.
  • When a Micromine Pitram Mobile device with high or low-precision GPS is installed on a loader or a truck, for example, most of the communication between the equipment and the database is automatic. However, an equipment operator may still use his device to communicate with the Control Room Operator via text messages.
  • Automation is greatly enhanced if a Digital Terrain Model (DTM file) is draped over an aerial photograph of the site, which is then displayed in Micromine Pitram 3D. This configuration means that the equipment can be tracked as it moves around the mine. Warnings will be automatically transmitted, for example, if a truck is about to dump ore onto a waste dump, or if a loader moves out of an ore zone. The Control Room Operator is able to see these warnings in the Data Acquisition screen.

Typical events recorded in Micromine Pitram include:

Equipment States

States are used to record equipment hours and are categorised into operating, idle and downtime. Within each of these, individual codes are broken out for various types of operating, idle, and maintenance codes to give the level of detail required for the site (Hourly Hire, Refueling, Standby, PM 500hr Services, CM Engine Radiator Repair). This information is used for reporting equipment usage, availability, productivity rates, mean time between failure, etc.

Allocations

Trucks are allocated to loading equipment before a Dump event can be recorded. This allocation allows for the reporting of production figures against the loading equipment as well as the hauling equipment. The Source location is derived from the location of the Loading equipment. The Destination location is determined from the Hauling equipment.

Locations

Locations are recorded against equipment to determine where material is being mined, where material is dumped, where equipment is at the end or start of shift, haul distances, etc. Locations are not only defined for mining and dumping areas, but also for workshops, go-bays, fuel points, etc.

Movements

Movements are usually recorded by logging truck dumps or loader buckets. These events use the Location information to determine the Source and Destination as well as the Material type. Materials can include any type of material moved; including production material, topsoil, gravel, etc. This information is used for reporting Movements by Location and material type, productivity rates, cycle times, etc. Movements can be reported in BCMs and Tonnes, and as survey-corrected movements.

Personnel

Personnel details can be recorded for any employees or contractors the site wishes to monitor. By recording activities and allocating personnel to equipment, records can be maintained of productivity for the individual on each type of equipment, last operated date, time-sheet details, training details, leave, etc.

Measures

Data can be captured for; measures relating to fuel, drill holes and metres drilled, bolts (and other consumables), advance, rail events, equipment hour meter readings, etc. These can be used for reporting total usage, consumption rates, drill rates, etc.