EquipDeallocatedFromLocER

Automatic status change required: The bogger leaves a mining face and its status is set to Tramming.

Reference data group: EquipDeallocatedFromLocER This status change is very similar to EquipAllocatedToLocEr except that it is applied when a unit is allocated away from a location. The way in which the following rules are implemented will depend on the active list defined for the Locations attribute.

Status Selection Mode: Automatic - Prompt

Procedure

Two similar rules are defined:

  • EquipAllocatedToLocER. The active list for the Locations attribute defines all the locations to which the unit of equipment is travelling. If the unit is allocated to a location that is a member of this active list, the status change is triggered.
  • EquipDeallocatedFromLocER. The active list for the Locations attribute defines all the locations from which the unit of equipment has travelled. If the unit is currently at one of the locations in the active list and is allocated to a location that is not a member of this active list, the status change will be triggered.

In Reference Edit

To defining the EquipDeallocatedFromLocER rule:

  1. Go to Groups | Configuration Items | States | Equipment Status Rules | EquipDeallocatedToLocER.
  2. Select Checkout on the header toolbar to add a token to the group.
  3. Click New EquipDeallocatedToLocER on the header.
  4. Enter the following definitions:
    OptionSelect
    General
    CodeDEALLOCATEBOGGER
    DescriptionBogger Leaving Location: Tramming
    AbbreviationBogger Leaving Location: Tramming
    Attribute
    Equipment*

    Bogging Equipment

    Select the appropriate active list from the list of Micromine Pitram | Equipment active lists.

    Locations*

    UG Loading Locations

    This active list defines the list of locations that the unit is leaving. If the bogger is allocated to a location that is not a member of this list, the status change will be triggered.

    InitialEquipmentStates*

    Loading States

    The unit is currently in one of the listed states.

    StatusSelectionMode*

    Automatic - Prompt

    You will be able to select or reject the defined status.

    ManualSelectionStates*

    Loading States

    If the StatusSelectionMod is ManualSelection, the states listed in the selected active list will be presented. The Control Room Operator will manually select the appropriate status from this list.

    AutomaticSelectionStatus*

    Tramming

    If the StatusSelectionMode is any of the Automatic modes, Tramming is the status that will be applied to the unit of equipment.

  5. Click OK to save the settings. The dialog will close.
  6. Select Checkin on the workspace toolbar to check in the changes that you have made.
  7. Click Publish on the navigation pane header. The dialog will open.
  8. In the Publish dialog, click Publish. You will receive a message to say that publishing has been successful. Click OK to close the message.

Wait till the version number of the reference edit group where you were working updates to the latest version.

Part ii: Working in Data Acquisition.

  1. Make sure the status bar shows the latest version and the Underground panel is displayed on a canvas.
  2. Right-click on Bogger1 and enter the following:
    OptionSelect
    Set Primary StatusOperating
    Allocate to Location

    UGLocA

    This location will probably be set already. It is a member of the UG Loading Locations active list.

  3. Right-click on Bogger1 again and select Allocate to Location.
  4. Select Go Line. Bogger1 was at one of the UG Loading Locations and has been allocated to the Go Line. The latter location is not a member of the UG Loading Locations. When deallocating, the reference is to the location that the unit is coming from: it is coming from a loading location, therefore the status changes to Tramming.

    Equipment Bogger1 is LEAVING location 'UGLocA' Do you wish to change equipment status for Bogger1 to "Tramming'.

  5. Click OK to save the status change. The message will close.

At your site, to work with the 'allocate to' and the 'deallocate from' rules you must be careful to select the appropriate Locations active list.

You need to identify locations that the unit is:

  • Allocated to. This is for the EquipAllocatedToLocER rule.
  • Leaving. This is for the EquipDeallocatedFromLocER rule.

The active list for both rules may be the same active list.